The origins of RAM (Die-Sinker) EDM Machines
Ram type (also called sinker type) EDM was the first type of Electrical Discharge Machining used in the manufacturing process. I was lucky enough to see the first EDM machine made for the purpose of eroding metal. Most historians give credit to a metallurgist couple...
Categories:
What is the proper programming format for a tapered or 4-axis profile that requires manual wire threading of an angular start hole?
This is a great question since an angular start hole is a situation that commonly occurs in mold tooling lifter pocket or ejector pin details. As part of this process, a position for manual wire threading needs to be determined within the profile, and an M01 stop...
Categories:
Wire EDM: GIGO
Garbage In Garbage Out: Mistakes in the Wire EDM are most often made before the start button is pressed. As the operator, you are often pushed to get the machine cutting, because when it’s not cutting, it’s not making money, right? WRONG! What if in the process of...
Categories:
Wire EDM: Common Causes of Wire Breakage
Much research has been done on the issue of wire breakage during the machining process. But before we explore the types of wire that can be used to decrease wire breakage in certain materials, we must first look at what causes wire breakage in general. Current Density...
Categories:
Wire EDM: What makes a WEDM last—and how long?
Let us look at a few reasons why a Wire Electrical Discharge Machine should last many years and produce perfect parts from cradle to grave. The machining pressures and speeds are low. As the wire cuts through the electrically conductive part, it moves at a speed...
Categories:
Wire EDM: How Much Better Is Bigger?
Large-diameter wire for EDM has been around for decades, but just recently it has taken the market by storm. To understand how and why this is happening I will go back to my personal experiences as a WEDM operator. In 1976, the industry-standard wire diameter was...
Categories:
Wire EDM: Top Ten Cleaning Tips
Wire Spool Area: The interval of cleaning and maintenance in the wire spool area is easier to remember as you replace empty wire spools frequently. A light blast of air or wiping with a cloth is sufficient for general maintenance in this area. Be sure to remove excess...
Categories:
Wire EDM: Key Physical Properties
Key physical properties that electrical discharge machine wires must incorporate are: Conductivity: A high and good conductivity rating is imperative in light of the fact that, at any rate hypothetically, it implies wire may convey additional current, that compares to...
Categories:
What is the best type of coated wire to use for achieving the highest quality surface finish?
There are many different types of coated wire available today, so it is important to understand the specific application for which a wire was designed and intended. There isn’t a single wire type that is best for every application. Some are designed for speed,...
Categories:
Wire EDM: How We Got Here
More than 45 years ago, a young tool and die maker and plastic injection mold builder named Gordon Shumway saw the EDM process in its infancy and made learning the process his quest. Since then, he’s worked with various major manufacturers as a research and...
Categories:
What’s the best way to create a 4-Axis program to ensure the best accuracy and eliminate wire lines and facetted geometry?
This question hits on many areas that relate to the machine as well as CAM system programming techniques. Here are a few items to address and review for best results: MACHINE ITEMS: Maximum Taper Angle: It’s important to identify the maximum taper angle that a...
Categories:
What is the proper programming format for a tapered or 4-axis profile that requires the manual wire threading of an angular start hole on a wire EDM machine?
Angular start holes commonly occur when machining mold tooling lifter pockets and ejector pin details. As part of this process, a position for manual wire threading needs to be determined within the profile, and a M01 Stop Point should be created within the NC...
Categories:
What is the best type of coated wire to use for high-precision machining applications?
It is important to understand that certain types of coated wire can degrade the accuracy output from the machine. Part accuracy can be reduced with coated wire as a result of the wire’s outer coating eroding and vaporizing more quickly than a standard brass...
Categories:
What does a Wire EDM machine require for regular maintenance?
Wire EDM is a versatile and useful machining process. One of the prerequisites for repeatability, reliability and accurate cutting results is proper machine maintenance. A Wire EDM machine may be one of the most maintenance-intensive pieces of equipment in the shop...
Categories:
Wire EDM: To D or Not, and Y
Programming with offsets The Use of D offsets was used to shorten and simplify the programing process. We needed a process to edit without rewriting the entire program to make minor changes, so let’s look at what was involved and Y the use of D offsets was needed. The...
Categories:
Wire EDM: Transport Systems
To understand the need for controlling the wire from the spool to the scrap bin or scrap roll, we look at each component and its importance in the wire EDM transport system. We’ll look at where we started and then where we are today. At the heart of this system...
Categories:
What Is the Best Type of Coated/Stratified Wire to Use?
This is a common question and one that does not have a simplistic answer, as there are many different machine and application variables that must be examined in order to determine which wire type is best. In order to evaluate your wire needs, you’ll want to answer...
Categories:
The Best Way to Store Wire Spools
When storing new or partially used wire spools, they should not be stored with the wire laying horizontally (laying on the spool flanges). It is common to store a spool by laying it on the flanges so that the spool does not roll away
Categories:
Common electrode materials for electrical discharge machining in a sinker EDM with oil-based dielectric
When choosing an electrode material, you must consider many factors. The usual first decision is, should you choose a metallic or non-metallic electrode? Depending on the material to be removed, this can be as simple decision. Carbides and sintered metals require more...
Categories:
EDM and Linear vs Ballscrews
An overview of the two most common drive systems in EDM machines today and what differences they bring to the EDM process. Ballscrews have been with us for many years and have proved to be accurate, reliable, easy to maintain and easy to fit many different...